Your AEG coffee machine can suddenly stop working for a number of different reasons. Sometimes, the remedy is as simple as adjusting the mill, while in other cases you may have to take the machine apart to fix it. The troubleshooting tips below will guide you through the process of the coffee machine repair, no matter whether it is a serious issue or a minor malfunction.
AEG PE, CG coffee machine troubleshooting
| DISPLAYED MESSAGE | POSSIBLE CAUSE | REMEDY |
|---|---|---|
| FILL TANK | The water tank is empty or positioned incorrectly | Fill the tank with water and/or insert it correctly, pushing it as far as it will go |
| GROUND TOO FINE ADJUST MILL AND (alternating with) PRESS OK | • The grinding is too fine and the coffee is delivered too slowly. • The machine cannot make the drink as there is air in the hydraulic circuit Possible cause: the filter has not been installed correctly. | • Turn the grinding adjustment knob one click clockwise towards "7". • Make sure the filter is propertly installed and that the installation has been carried out correctly. |
| GROUND TOO FINE ADJUST MILL AND (alternating with) PRESS OK (then) FILL TANK | The tank has been removed during delivery | Insert the tank and press the OK icon (B9). "HOT WATER PRESS OK" is displayed |
| EMPTY WASTE COFFEE CONTAINER | The waste container is too full or more than 3 days have passed since you last made coffee (this guarantees correct hygiene of the machine). | Empty the waste container and clean, then replace. Important: when removing the drip tray, the waste coffee container MUST be emptied, even if it is not completely full. If this is not done, when you make the next drink, the waste container may fill up more than expected and clog the machine. |
| INSERT WASTE COFFEE CONTAINER | After cleaning, the waste container has not been replaced | Open the service door and insert the waste container. |
| ADD PRE-GROUND COFFEE | • The "pre-ground coffee" function has been selected without placing any pre-ground coffee in the funnel. • The funnel is bloc- ked. | • Extract the appliance and place pre-ground coffee in the funnel. • Empty the funnel with the help of a knife |
| PLEASE DESCALE! | The machine must be descaled. | The machine must be descaled. |
| LESS COFFEE | Too much coffee has been used | Select a milder taste or reduce the quantity of preground coffee, then make the drink again. |
| FILL BEAN CONTAINER | The coffee beans have run out | Fill bean container |
| INSERT BREWING UNIT | The brewing unit has not been replaced after cleaning. | Insert the brewing unit |
| CLOSE DOOR | The service door is open | Close the service door. |
| GENERAL ALARM! | The inside of the appliance is very dirty. | Clean the inside of the appliance thoroughly |
| REPLACE FILTER! | The water softener filter must be replaced. | You must immediately replace the filter |
AEG LM 5100 (AEG A Modo Mio Lavazza) coffee maker troubleshooting
Espresso capsule system
| Problems | Causes | Solutions |
|---|---|---|
| The machine does not turn on. | The machine is not connected to the power source | Connect the machine to the power source. |
| The pump is very noisy. No water flow. | No water in the tank. | Fill the tank with fresh drinking water. 1. Prime the water circuit. 2. Check correct water tank position |
| The loading lever doesn't reach the brewing position. | Capsule inserted incorrectly. | Empty the used capsule compartment. |
| Repeat the sequence, open and close the lever. If that is not enough remove the capsule manually from the compartment after unplugging the machine. | ||
| The coffee is cold. | Preheat the cup with the hot water. | |
| The coffee is brewed too fast, the brewed coffee is not creamy. | Capsule already used. | Open the lever and insert a new capsule. |
| Coffee is not brewed or brewed in drips only. | Coffee spout is clogged. | Clean the coffee spout. |
| Hot water / steam is not dispensed. | Hot water / steam spout is clogged. | Clean the steam spout with a needle (the machine needs to be unplugged and the steam / hot water knob needs to be closed). |
| The milk does not froth. | Not suitable milk. | Use fresh, partially skimmed milk. |
| The milk is too hot. | Use milk at refrigerator temperature. | |
| The hot water / steam spout is clogged. | Clean the steam spout with a needle (the machine needs to be unplugged and the steam / hot water knob needs to be closed) | |
| The machine requires a lot of time to heat up | The machine has limescale build up. | Descale the machine. |
| FLASHING LIGHTS | The machine requires a lot of time to heat up | The machine may have lime scale build up, descale the machine. |
| NO COFFEE BREWED/ LEAKING UNDER MACHINE | Remove the coffee dispensing spout by pulling the spout fully down and remove it by pulling towards you. Clean and put back in place. or Prime the machine or Empty drip tray | |
| LEVER STUCK | Empty capsule drawer Or The last capsule not fallen in to correct position. Open and close the level or unplug the machine and manually push down. | |
| NOISY MACHINE | Fill tank with fresh cold water and ensure it is fitted correctly. | |
| PROBLEMS WITH STEAM ARM | Blockage of steam spout: | Remove steam wand from below the rubber holder and clear blockage in the steam spout (e.g. with a pin). NOTE: Don’t forget to wipe the steam arm and open and close the steam dial for a few seconds after every use to keep it hygienic and prevent blockages. |
AEG FRESH AROMA KAM300 coffee maker troubleshooting
| Problem | Solution |
|---|---|
| The appliance does not work. | Put the mains plug in the wall socket. Make sure that the voltage indicated on the appliance corresponds to the local mains voltage. Fill the water reservoir with water. |
| When I use the grinder, the coffee is too weak. | Make sure the number of cups you select with the 2-10 cups button is consistent with the amount of water in the water reservoir. Please keep in mind that the appliance uses all the water in the water reservoir. Use the STRENGTH button to set the coffee strength to 'strong' . When you use coffee beans, make sure you do not press the preground coffee button, as this switches off the grinder. Use beans of a stronger blend or flavour. To increase the coffee strength, select a higher number of cups with the 2-10 cups button than the number of cups you fill the water reservoir with. |
| When I use pre-ground coffee, the drink is too weak. | Make sure the amount of pre-ground coffee in the filter is consistent with the amount of water in the water reservoir. Please keep in mind that the appliance uses all the water in the water reservoir. Use ground beans of a stronger blend or flavour. To increase the coffee strength, increase the amount of pre-ground coffee or decrease the amount of water. |
| I have set the coffee strength to 'strong' with the STRENGTH button, but the coffee is too weak. | When the grinder is switched off, you cannot change the coffee strength with the STRENGTH button. In this case you can only increase the drink strength by increasing the amount of pre-ground coffee or decreasing the amount of water, or by using beans of a stronger blend or flavour. |
| The filter overflows when I remove the jug from the appliance while it is brewing coffee. | If you remove the jug for more than 20 seconds during the brewing process, the drip stop causes the filter holder to overflow. Also note that the drink does not reach its full taste before the end of the brewing process. Therefore we advise you not to remove the jug and pour out the coffee before the end of the brewing process. |
| The appliance continues to drip long after the brewing process has ended | The dripping is caused by condensation of steam. It is completely normal that the appliance drips for some time. If the dripping does not stop, the drip stop may be clogged. To clean the drip stop, push it to open it and then rinse it under the tap. If you remove the jug for more than 20 seconds during the brewing process, the drip stop causes the filter basket to overflow. |
| The coffee is not hot enough. | Place the jug properly on the hotplate. Make sure that the hotplate and the bottom of the jug are clean. Use thin cups, because they absorb less heat from the coffee than thick cups. Do not use milk that comes directly out of the fridge. Descale the appliance. |
AEG CS coffee machine troubleshooting
| Problem | Solution |
|---|---|
| The coffee is not hot | The cups have not been preheated. • Pre-heat the cups by rinsing them in hot water or leaving them for at least 20 minutes on the cup warmer tray • The infuser is too cold. Heat the infuser by pressing the *button (see under the table) button before making the coffee. |
| The coffee is not creamy enough | • The machine uses too little coffee during the infusion process. Turn the grinding quantity selector knob a little clockwise. • The coffee is ground too coarse. Turn the grinding adjustment knob one click anticlockwise. • Wrong type of coffee. Use a type of beans for fully automated espresso makers. |
| The coffee comes out too slowly | • The coffee is ground too fine. Turn the grinding adjustment knob one click clockwise. • The machine uses too much coffee during the infusion process. Turn the grinding quantity selector knob a little anticlockwise. |
| The coffee comes out too quickly | • The coffee is ground too coarse. Turn the grinding adjustment knob one click anticlockwise. • The machine uses too little coffee during infusion. Turn the grinding quantity selector knob a little clockwise. |
| The coffee does not come out of one of the spouts | • The outlet is blocked. Scrape the remains of dry coffee accumulated with a needle |
| Turning the steam knob, no steam comes out of the milk frother | • The holes in the spouts are clogged. Clean the holes in the milk frother and the milk frother nozzle. |
| Pressing the 1 cup or 2 cups button the machine does not deliver coffee, but only water | • Ground coffee may be blocked in the funnel. Remove the ground coffee inside the funnel, using a knife. Then clean the infuser and the inside of the machine. |
| Pressing the 'Start' button, the machine does not switch on | • The machine is not plugged in. Check that the power cable is plugged into the power outlet. |
| The infuser cannot be removed for cleaning | • The machine is on. The infuser can only be removed if the machine is off. Turn the machine off. Attempting to remove the infuser with the machine on will risk causing damage. |
| Ground coffee is used (rather than beans) and the machine does not deliver the coffee. | Too much ground coffee has been added Remove the infuser and thoroughly clean the inside of the machine. Repeat the operation using a maximum of 2 level measures of ground coffee. |
| The coffee does not come out of the spouts, but rather around the service door | • The holes in the spouts are clogged with dry coffee. Scrape the holes with a needle. • The mobile drawer inside the service door is blocked and cannot swing. Thoroughly clean the mobile drawer,above all near the hinges, so that they swing smoothly |
